Clik here to view.
Support Question of the Week: What Are the Best USB Protocol Analyzers and...
I need to analyze USB communication between an Android smartphone and an embedded board that is equipped with an FTDI USB host chip, FT312D. The USB link does not run consistently. The USB...
View ArticleClik here to view.
Support Question of the Week: How Do I Connect the SPI Host Adapter Signal...
I'm trying use the CheetahTM SPI Host Adapter to program Micron SPI flash devices N25Q256A and N25Q00A. I have two questions: Do you currently support programming N25Q256A and N25Q00A? Listed below...
View ArticleClik here to view.
Support Question of the Week: Which SPI Host Adapter is Best for Simulating a...
I am looking to use an SPI host adapter as a master to simulate a MCU (multipoint control unit) for an application - this MCU in the design phase. Another existing MCU will be used as the SPI slave. In...
View ArticleClik here to view.
Support Question of the Week: How Do I Support Reading 16-Bit SPI Data...
I am trying to sample IMU (inertial measurement unit, M-G362PDC1 by Epson) data at 100 Hz but my setup misses some of the 16-bit SPI data samples. Here’s my setup: I am using a MacBook as the host and...
View ArticleClik here to view.
Support Question of the Week: How Can I Quickly and Program SPI Memory...
I will be using the Aardvark host adapter to program a series of SPI memory devices. This is a high volume project - what is the fastest and easiest way I can do this? Thanks for your question! The...
View ArticleClik here to view.
Support Question of the Week: How Do I Use the Komodo CAN Interface to View...
I just purchased the KomodoTM CAN Interface and I need to count the number of retried transmissions on the CAN bus. How can I do that? Please advise. Thanks for your question! The Komodo CAN Interface...
View ArticleClik here to view.
Support Question of the Week: How Can a GPIO Interface be Created for the...
I am using the CheetahTM SPI Host Adapter and would like to use it to program an SPI device. To set this device to programming mode, I need to do the following: At power on, set the Reset pin, and set...
View ArticleClik here to view.
Support Question of the Week: Using the Aardvark I2C/SPI Host Adapter, How...
I have multiple AardvarkTM I2C/SPI Host Adapters and I plan to use them for a production flow; programming SPI EEPROMs (Microchip 93AA56AT-I/OT). It looks like this device is not supported by Flash...
View ArticleClik here to view.
Support Question of the Week: To Save Board Space and Not Include a Connector...
I am working on a new design that will be installed in a system. To do so, I need to save board space. My target USB bus is inside of an embedded system. To analyze and verify the results, I'll need to...
View ArticleClik here to view.
Support Question of the Week: How do I Control the SPI Slave Responses from...
I am using the Aardvark I2C/SPI Host Adapter in the SPI Slave mode. How can I specify multiple responses for the Aardvark to return, such that each packet returns a different response? To provide some...
View ArticleClik here to view.
Support Question of the Week: How Do I Clear the Saturated Buffer When Using...
I am using a Komodo CAN Duo Interface with the LabVIEW software and Komodo LabView Drivers (VI). I write a packet, and when I read the bus, the packet I am looking for has already been sent by the...
View ArticleClik here to view.
Support Question of the Week: With a USB Protocol Analyzer, What is the...
I need to capture USB 2.0 bus data between a scanner and computer. The information is scanned from a coupon, and then OCR (optical character recognition) is applied to identify the information on that...
View ArticleClik here to view.
Support Question of the Week: How Can I Use one Cheetah SPI Host Adapter to...
I have two different SPI devices and I need to transmit two different command settings. Because of the separate SS (slave select) signal pins, it looks like the Cheetah host adapter should work with...
View ArticleClik here to view.
Support Question of the Week: How Do I Communicate to the Komodo CAN Duo...
I am trying to communicate to the Komodo CAN Duo Interface device using the Keysight VEE software - a graphical IDE that is similar to National Instrument's LabVIEW. VEE cannot import in "enum" types....
View ArticleClik here to view.
Support Question of the Week: How do I Configure the Cheetah SPI Host Adapter...
I plan to use the Cheetah SPI Host Adapter for a half-duplex 3-wire SPI slave device. Can the Cheetah adapter be configured to interface with a 3-wire SPI? Is there anything special I would need to do?...
View ArticleClik here to view.
Support Question of the Week: How Can I Use the Cheetah SPI Host Adapters to...
I have two different SPI devices and I need to transmit two different command settings. Because of the separate SS (slave select) signal pins, it looks like the Cheetah host adapter should work with...
View ArticleClik here to view.
Support Question of the Week: How Can I Use a Single SPI Host Adapter to...
I have two different SPI devices and I need to transmit two different command settings. Because of the separate SS (slave select) signal pins, it looks like a Cheetah host adapter should work with...
View ArticleClik here to view.
Support Question of the Week: How Can I Make Third Party Open Source Software...
I am developing an interface for a planter that is connected to a tractor with a display monitor via CAN bus. For the agricultural industry, I found an open source program (ISOAgLib) that could work...
View ArticleClik here to view.
Support Question of the Week: Did You Know You Can Batch Program I2C Memory...
You can batch program devices using the Aardvark I2C/SPI Host Adapter and any of the following applications: the Control Center Software, the Flash Center Software or the Aardvark Software API....
View ArticleClik here to view.
Support Question of the Week: How Do I Configure Conditions for a USB...
I plan to run a design verification tests (DVT) for long periods. For part of the DVT, I'll need to continue running the test and capture data as errors occur. For another part of the DVT, I'll need to...
View Article