Quantcast
Channel: Total Phase Blog
Browsing all 822 articles
Browse latest View live

Image may be NSFW.
Clik here to view.

Support Question of the Week: How Do You Transfer SPI Data Using the Aardvark...

Today's article is based on a new Knowledge Base article, Sending SPI Messages Between Two Aardvark adapters Using Aardvark LabVIEW. The AardvarkTM I2C/SPI Host Adapter is often used with LabVIEW to...

View Article


Image may be NSFW.
Clik here to view.

Question of the Week: What are the features of the Komodo CAN interface and...

We are starting to use the KomodoTM CAN Duo Interface - it is very easy to set up and use. We like the activity LEDs and the choice of connectors. The ability to make the device active or passive is...

View Article


Image may be NSFW.
Clik here to view.

Support Question of the Week: Which SPI Host Adapter and Which Software...

I will be programming Serial flash and I see that your Cheetah and Aardvark host adapters both support SPI programming. I have two questions: Which is more appropriate for gang programming in-system,...

View Article

Image may be NSFW.
Clik here to view.

Support Question of the Week: How do I Set Up and Identify Multiple Cheetah...

We have a new product in development that will contain a new Microsemi FPGA device and the Micron Flash N25Q00AA13G1240E - both need to be programmed. They will be built into a panel, eight to a panel....

View Article

Image may be NSFW.
Clik here to view.

Support Question of the Week: Which Host Adapters Can I use to Communicate to...

We have decided to use the AardvarkTM I2C/SPI Host Adapter for the purpose of I2C and SPI communication with our device under test (DUT). The scope is set up to act as a slave in I2C communication and...

View Article


Image may be NSFW.
Clik here to view.

Support Question of the Week: How Do I Use the Cheetah SPI Host Adapter with...

I just started using your CheetahTM SPI Host Adapter and high speed flash sockets to program 1.8V Micron flash devices, N25Q064A. The Total Phase socket boards I use provide about 3V for VCC, even when...

View Article

Image may be NSFW.
Clik here to view.

Support Question of the Week: How Can I Best Capture SPI Bus Data for...

I am debugging a TI C2000 microcontroller using SPI.  The setup: The PC (personal computer) side of the SPI bus is the slave. The packet rate is 10kHz, 100 bits/packet. Looking at the specifications...

View Article

Image may be NSFW.
Clik here to view.

Support Question of the Week: How is a Batch File Run on the Control Center...

We recently purchased an AardvarkTM I2C/SPI Host Adapter. We're using it to read two packets from the register from a PLX chip. We're trying to use the batch mode of the Control CenterTM Software, but...

View Article


Image may be NSFW.
Clik here to view.

Support Question of the Week: Using the Beagle USB Protocol Analyzer, How Do...

I am using the BeagleTM USB 480 Protocol Analyzer, and I want to use a decode script, such as Mass Storage, to display the transactions as class specific commands. Can the Data CenterTM Software...

View Article


Image may be NSFW.
Clik here to view.

Support Question of the Week: How do I Communicate with a SMBus Slave Device...

I’m using the AardvarkTM I2C/SPI Host Adapter to communicate with a SMBus slave device (Accuron PS401). What I'm looking to do is establish communication with the chip and verify the communication with...

View Article

Image may be NSFW.
Clik here to view.

Support Question of the Week: How Can I Use the Beagle I2C/SPI Protocol...

  I have the BeagleTM I2C/SPI Protocol Analyzer, and I need to capture any glitches that may occur on an SPI bus where multiple SPI slaves are attached. How can I capture data from multiple SPI Slaves...

View Article

Image may be NSFW.
Clik here to view.

Support Question of the Week: What are the Available Software API Examples...

I'm starting to use the KomodoTM Duo Interface. I need to create some programs to run tests on prototype devices for a CAN bus. I have a couple of questions: Do you have any Komodo software examples in...

View Article

Image may be NSFW.
Clik here to view.

Support Question of the Week: Using a Protocol Analyzer, How Does the Data...

I have a question about results I see when I capture USB trace files. Using a BeagleTM USB Protocol Analyzer , I was browsing two separate USB trace files with the DataTM Center Software. On one...

View Article


Image may be NSFW.
Clik here to view.

Support Question of the Week: How Do I Integrate the Aardvark I2C/SPI Host...

I have an AardvarkTM I2C/SPI Host Adapter. To configure communication for I2C devices,  I'll be using MATLAB® with the Aardvark adapter. Can you tell me how to do that? I am using Windows 7...

View Article

Image may be NSFW.
Clik here to view.

We've reached the (Flash Memory) Summit!

The booth is ready for visitors Total Phase is exhibiting at the Flash Memory Summit in Santa Clara, California.  We're showing off our entire range of debugging and development tools for USB, I2C,...

View Article


Image may be NSFW.
Clik here to view.

Support Question of the Week: Did You Know That a Beagle Protocol Analyzer...

The BeagleTM I2C/SPI Protocol Analyzer is a cost-effective tool for easily sniffing I2C and SPI traffic. But did you know that it could also be integrated with other systems? Here are two examples of...

View Article

Image may be NSFW.
Clik here to view.

Support Question of the Week: Did You Know You Can use Cheetah API Software...

I'm using the CheetahTM SPI Host Adapter as an SPI controller, and I need to control Cheetah with MATLAB.  I've tried modifying the h. files and then generate the .m files for MATLAB, but I can't get...

View Article


Image may be NSFW.
Clik here to view.

Support Question of the Week: What Makes the Beagle USB Protocol Analyzer...

There are many effective uses for a Beagle USB Protocol Analyzer: sniff and analyze many products, including mass storage, HIG, many classes, USB-Ethernet devices, IP-layer decoding, pass data to...

View Article

Image may be NSFW.
Clik here to view.

Support Question of the Week: How do You Use the Host Adapter GPIO Features...

I’m new with the Aardvark I2C/SPI host Adapter, and I’m using it in SPI mode. It seems it does not have pins that are dedicated for sending interrupts. Could I use another pin to send interrupt signals...

View Article

Image may be NSFW.
Clik here to view.

Support Question of the Week: How Can I Interface the Beagle SPI Protocol...

I have a question about interfacing the BeagleTM IC2/SPI Protocol Analyzer with my setup. I am using the ST Microelectronics STM32F071CB as the SPI master and the Nuvoton ISD2115 as the SPI slave...

View Article
Browsing all 822 articles
Browse latest View live