Clik here to view.
How do I Provide Lower Signal Voltage Logic and Power Levels to SPI Target...
Question from the Customer: I need some help with programing and testing SPI chips on my board. I am using the Aardvark I2C/SPI Host Adapter with the 10-Pin Grabber Clip Split Cable. I am new with the...
View ArticleClik here to view.
Can I Use and Identify Multiple Aardvark I2C/SPI Host Adapters when Reading...
Question from the Customer: I have some questions about using the Aardvark I2C/SPI Host Adapter. I am reading and writing to multiple I2C and SPI devices, and I need to control multiple Aardvark...
View ArticleClik here to view.
How Do I Modify XML Files to Use the Cheetah SPI Host Adapter with the Flash...
Question from the Customer: We use several Cheetah SPI Host Adapters for programming in our production runs and the R&D department. We have been using Atmel AT45DD041D-SSU SPI serial data flash...
View ArticleClik here to view.
Using the Aardvark I2C/SPI Host Adapter, How Do I a Perform "Master Register...
Question from the Customer: I am using the Aardvark I2C/SPI Host Adapter with the Control Center Serial Software. In the I2C Control section, I see that I can easily perform a "Master Register Read". I...
View ArticleClik here to view.
Did You Know You Can Use the Komodo Can Duo Interface with CAN High Level...
Question from the Customer: I am new to CAN, and I have some basic questions. Does the Komodo CAN Duo Interface support running as a Host? I have a device with a Dual CAN interface that runs as a...
View ArticleClik here to view.
How Do I Configure an Aardvark I2C/SPI Host Adapter or a Promira Serial...
Question from the Customer: I am interested in your host adapters, the Aardvark I2C/SPI Host Adapter and the PromiraTM Serial Platform, and I have a few questions about how they handle SPI. My SPI...
View ArticleClik here to view.
Did You Know You Can Shift I2C or SPI Logic Signal Levels without a Level...
Question from the Customer: I am trying to use the Aardvark I2C/SPI Host Adapter or the Cheetah SPI Host Adapter to program an SPI chip that uses 1.8V as the high logic level. Do the Aardvark or...
View ArticleClik here to view.
How Can I Set Up the I2C/SPI Host Adapter for Synchronous I2C Reads from Two...
Question from the Customer: We are using the Aardvark I2C/SPI Host Adapter and the GPIO to test our prototype I2C-to-CEC Translators. These prototype boards are connected together, and each one is...
View ArticleClik here to view.
How Does the Aardvark I2C/SPI Host Adapter Read, Verify and Record Binary Data?
Question from the Customer: We are considering the Aardvark I2C/SPI Host Adapter for an upcoming project. Can the Aardvark adapter be used for the following tasks? Read the device’s contents (in binary...
View ArticleClik here to view.
Which Total Phase Products Support 16-bit SPI Data Transactions with the...
Question from the Customer: I have both the Aardvark I2C/SPI Host Adapter and the Beagle I2C/SPI Protocol Analyzer. In addition to monitoring, I am trying to perform 16-bit read and write operations...
View ArticleClik here to view.
Selecting the Tools to use as an SPI Master to Provide a Clock Signal and...
Question from the Customer: I am trying to use the Beagle I2C/SPI Protocol Analyzer and the Data Center Software to read the I2C bus to capture the data output from an LIS302DL accelerometer. The...
View ArticleClik here to view.
Using the Total Phase Komodo CAN Interfaces for Specialized Test and...
Question from the Customer: We are using the Aardvark I2C/SPI Host Adapter and the Cheetah SPI Host Adapter for our embedded microprocessor development project. They work great and really help reduce...
View ArticleClik here to view.
What Causes the Split Orphaned Packets that the Beagle USB 480 Protocol...
Question from the Customer: I am using the Beagle USB 480 Protocol Analyzer, and have a question about the errors that the Data Center Software captures and reports. Following is a block diagram of my...
View ArticleClik here to view.
How Do I Set Up the Promira Serial Platform to Run an Async Queue or a Sync...
Question from the Customer: I'm trying to use the Promira Serial Platform to write and read to SPI devices: one with an async queue, and another with a sync queue. Can you provide examples to do this?...
View ArticleClik here to view.
Using the Beagle USB 480 Protocol Analyzer and the Data Center Software to...
Question from the Customer: I am using the Beagle USB 480 Protocol Analyzer for USB 2.0 captures. I’m trying to get information and measure timing of every IN-NA“ at a specific point on an existing...
View ArticleClik here to view.
What are the SPI Timing Requirements for the Aardvark I2C/SPI Host Adapter to...
Question from the Customer: I am using the Aardvark I2C/SPI Host Adapter in SPI/GPIO mode as a slave. I set up a MISO message in the Control Center software (I’m using Windows), and the transaction log...
View ArticleClik here to view.
Which Beagle USB Protocol Analyzers Provide an External Trigger to Test a USB...
Question from the Customer: I need to measure timing from an event that produces a USB response in our device. I can trigger a scope off of the edge of the event but I need another trigger when the...
View ArticleClik here to view.
How to Select Which USB Protocol Analyzer to Use to Monitor Output Conditions...
Question from the Customer: We have the Beagle USB 480 Protocol Analyzer [RCA1] and it’s worked really well for us. We’re starting a new project that requires toggling one of the output-signals when...
View ArticleClik here to view.
Use the Beagle I2C/SPI Protocol Analyzers and Total Phase Software API to...
Question from the Customer: I will be using two Beagle I2C/SPI Protocol Analyzers to monitor SPI devices, the data from two A/D converters. I will be using the Beagle Software API and C#. Normally, I...
View ArticleClik here to view.
To Run SPI Tests at a Higher Speed, How Do I Set Up Ethernet Connectivity and...
Question from the Customer: I am using the Promira Serial Platform to run tests and evaluations on the SPI bus of my application. I would like to do some benchmark testing over the Ethernet port. I...
View Article